Home Private Messages Search
    Products

Pac-Rat
Sleds
Fiberglass Products

  • Resins
  • Gel Coats
  • Fabrics
  • Accessories
  • Castings
  • Epoxy
  • Plastics
  • Urethane Foams
  • DivinyCell
Shelters
  • Spec Data
    1. Radio Shelter
    2. Standard Shelter
  • Pricing
  • Drawings
  • Engineering Data
  • Quality Control Procedures
  • Materials Used
    1. Polar
    2. Plexus
    3. Polyfoam
    4. MAT/Gel Coat
    •     Company
    · Home
    · Contact Us
    · Dealer Pricing
    · FAQ
    · Forums
    · How To Order
    · Plaschem Pictures
    · Private Messages
    · Search
    · Web Links
    RADIO SHELTER SPECIFICATIONS

    RADIO SHELTER SPECIFICATIONS

     

    GENERAL DESCRIPTION: The shelter shell will be molded fiberglass reinforced polyester laminated foam cored construction. Shelter will be a single piece and weigh less than 9001bs.

    DIMENSIONS: 12'X75"X75". Refer to drawings for additional measurement details. The shelter will have a 6" flange at the base to support added ballast for ground anchoring.

    GENERAL SHELTER CONSTRUCTION: Walls and roof will be sandwiched construction with no less than 1/8 inch Fiberglass Reinforced Polyester (FRP) laminate with a minimum of 15 mills polyester gel-coat applied to exterior and Vi" 4# density PVC foam bonded to the exterior laminate. 1/16" FRP laminate will then be applied over entire interior of shelter. Gel-coat will then be applied over the entire interior of shelter.

    FLOOR DETAIL: Floor will be made of ¾ " plywood and will be completely wrapped with Fiberglass Reinforced Polyester before being bonded to shelter.

    INTERIOR SHELVES: Two shelve units will be constructed in an "L" arrangement. Shelving will have a ½” upward flange. Each shelf will be capable of supporting 7501bs.

    SHELTER DOOR: Frame for shelter door will be Fiberglass Reinforced Polyester and will be molded into shelter walls. The door dimensions will be 31" x 42" and will be situated 15" above the floor of the shelter. The door will have three support hinges, a freezer style latch, and contain a neoprene seal.

    SHELTER VENTILATION: The shelter will contain ventilation tubes at the top and bottom to support proper ventilation.

    SHELTER SIDEWALL: The shelter sidewall will be reinforced for solar panel mounting.

    ANTENNA MOUNT: A schedule 40 section on PVC pipe will be installed vertically in the shelter to support antenna requirements. The PVC pipe will be supported at the top and bottom via wood cross supports. The PVC length shall be 69".

    SHELTER ENVIORMENTAL REQUIREMENTS: The shelter will support wind loads of 125MPH and snow loads of I50 lbs PSF.

    GROUNDING REQUIREMENTS: The shelter shall have a 5" x 7" ground plate mounted inside the shelter.

     

    HARDWARE REQUIREMENTS: Shelter hardware shall consist of non-corrosive material.

    SHELTER TRANSPORTATION: The shelter shall have a total of 4 ea 1.5" eyebolt installed on each corner to facilitate transportation by helicopter via slingload.

    Key features of 12' x 75 " x 75" antenna shelter.

     

    1. Transparent to R.F.

    2. FRP (Fiberglass Reinforced Plastic) seamless construction cored with W 4# density PVC foam core with a smooth molded exterior weatherproof finish.

    3. 150# psf snow load.

    4. 125 mph wind load

    5. Designed to sling under helicopter for transportation to remote sites.

    6. Four anchor points for ground anchors and a rock flange around bottom edge of hut for added ballast for ground anchoring.

    7. Sidewall reinforced for solar panel mounting.

    8. Built in vent system with top and bottom ventilation.

    9. Molded door, same construction as hut and fitted with a neoprene seal, freezer
      style latch and heavy duty hinges.

    10. Interior shelf able to support 700 pounds.

    11. Built in internal antenna mount.

    12. Total weight of shelter less than 900 pounds.

    13. All hardware is non-corrosive material.

    PH2BLUE Theme Modified By: Lorkan Themes